KÜBLER
LED Multifunction Counter, Codix 524
Indication counter with selectable functions such as: pulse counter, Frequency display, Position displays without limit values, Tachometer without limitvalues hour meters / timers and short-time meter.
LED display with 6 x digits, 8 mm. The counter is programmed using the two buttons at the front of the counter. These buttons can also be locked if so required. The counter has two counter inputs. Built-in memory backup EEPROM. Cable connection with screw terminal. The counter comes with clamps, gaskets and separate front frames to fit 25x50 mm panel holes. One for screw fitting and one without.
Pulse counter
For counting and adding pulses, also works as a position counter together with an angle sensor. The counter function is selected during programming
Cnt.dir | A=counter input | Quad | A=0° (designed for two-channel angle sensor) |
Up.dn | A=counting up | Quad2 | Same as quad, but multiplies the pulse count by 2. |
Chronometer/timer
For timing where the outputs are activated once a preset time is reached. Adjustable time ranges in one of the following ranges: h or min or sec, or h:min:s (e.g. 06 h:23 min:45 sec). The position of the decimal point determines the resolution of the time selected, e.g. whole seconds, tenths and hundredths of a second.
Tachometer/frequency/revolution counter
For displaying speed, e.g. rpm or metres per second. The counter speed can be selected between 30 Hz or 20 kHz.
User-friendly and versatile Large keys that can be operated even while wearing gloves Programming: Straightforward and consistent programming and operation using plain text programming. Access to programming is possible during operation, with safety prompts in place. Adjustable scaling on an individual basis Multiplication and division factors ranging from 0.0001 to 99.9999, enabling the calculation of corresponding units such as position in 1/10 mm and speed in RPM. Four different counter input types available for position display: counting direction, difference or addition mode, phase discriminator with single, double, or quadruple evaluation Frequency measurement with the option to display in 1/min or 1/sec Time counting: Pulse width or period duration measurement in hours, minutes, or seconds, along with real-time display capability Inputs: In addition to HTL inputs, devices with 4 to 30 V DC input level can also be used as parallel displays for PLC. Optional output: Provides a 0 signal for position and counting, allows for standstill monitoring at speed, and offers a 1 Hz cycle during active timing.
- 10-30 V dc
- Pulse, Frequency and time
- 6 Digit display
- 60 kHz Max. input
Selected variant
Technical data
| Connection | Screw terminal |
|---|---|
| Depth | 59 mm |
| Digit height | 8 mm |
| EMC | EN55011, 2004/108/EC, EN 61000-3-2, EN 61000-3-3 |
| Height | 24 mm |
| Input impedance, typ | 5 kΩ |
| IP class | IP65 |
| Material | Plastic |
| Mounting | Panel mount |
| Number colour | Red |
| Number of digits | 6 |
| Operating voltage dc max | 30 V |
|---|---|
| Operating voltage dc min | 10 V |
| Panel size | 24x48 mm |
| Polarity | Yes |
| Storage temperature max | 70 °C |
| Storage temperature min | -25 °C |
| Temperature operational max | 65 °C |
| Temperature operational min | -20 °C |
| Weight | 50 g |
| Width | 48 mm |
Downloads
Product description
Indication counter with selectable functions such as: pulse counter, Frequency display, Position displays without limit values, Tachometer without limitvalues hour meters / timers and short-time meter.
LED display with 6 x digits, 8 mm. The counter is programmed using the two buttons at the front of the counter. These buttons can also be locked if so required. The counter has two counter inputs. Built-in memory backup EEPROM. Cable connection with screw terminal. The counter comes with clamps, gaskets and separate front frames to fit 25x50 mm panel holes. One for screw fitting and one without.
Pulse counter
For counting and adding pulses, also works as a position counter together with an angle sensor. The counter function is selected during programming
Cnt.dir | A=counter input | Quad | A=0° (designed for two-channel angle sensor) |
Up.dn | A=counting up | Quad2 | Same as quad, but multiplies the pulse count by 2. |
Chronometer/timer
For timing where the outputs are activated once a preset time is reached. Adjustable time ranges in one of the following ranges: h or min or sec, or h:min:s (e.g. 06 h:23 min:45 sec). The position of the decimal point determines the resolution of the time selected, e.g. whole seconds, tenths and hundredths of a second.
Tachometer/frequency/revolution counter
For displaying speed, e.g. rpm or metres per second. The counter speed can be selected between 30 Hz or 20 kHz.
User-friendly and versatile Large keys that can be operated even while wearing gloves Programming: Straightforward and consistent programming and operation using plain text programming. Access to programming is possible during operation, with safety prompts in place. Adjustable scaling on an individual basis Multiplication and division factors ranging from 0.0001 to 99.9999, enabling the calculation of corresponding units such as position in 1/10 mm and speed in RPM. Four different counter input types available for position display: counting direction, difference or addition mode, phase discriminator with single, double, or quadruple evaluation Frequency measurement with the option to display in 1/min or 1/sec Time counting: Pulse width or period duration measurement in hours, minutes, or seconds, along with real-time display capability Inputs: In addition to HTL inputs, devices with 4 to 30 V DC input level can also be used as parallel displays for PLC. Optional output: Provides a 0 signal for position and counting, allows for standstill monitoring at speed, and offers a 1 Hz cycle during active timing.
Related
Safeguard systems with DC circuit protection
This blog talks all things DC circuit protection including the key components: electronic circuit breakers, fuses and current monitoring devices. As well as how to choose the right protection.
Recap of IATECH
Did you get a chance to visit IATECH at The Leicester Marriott Hotel? We had over 33 exhibitors and 8 fantastic Tech Talks throughout the day, Read all about the day, here.
Book your Cable Preparation Machinery Demo at OEM
To help experience the capabilities of Z+F machines first-hand, we provide an in-depth demonstration and workshop. These sessions will show the machines in action and allow you to understand their features and gain valuable insight into their operation and benefits.
OEM introduces IATECH - The Industrial Automation Technology Expo
We are thrilled to announce the launch of IATECH, THe Industrial Automation Technology expo at Leicester Marriott Hotel on 23rd October. The ultimate platform for showcasing our extensive product range and broad business areas, featuring over 50 leading suppliers under one roof!
Automation Components for Specialist Vehicles
The specialist vehicle industry can include automotive and EV, heavy vehicles such as agriculture and rail, and marine. This email takes you through some of the various products we offer for specialist vehicle applications.
Modern Power Distribution
This blog post delves into the key components, current trends, and best practices in power distribution, illustrating the significant impact these systems have on our daily operations and long-term energy strategies.
