PULS

Power supply 1-phase, 12 V dc Dimension C Series, Generation 2

Puls Dimension C-series stands for cost optimization without compromising quality, reliability or performance.

CP10 is the second generation C-series 1-phase that sets new records by using the latest technology and sophisticated thermal design. With an efficiency of 94.3%, the power losses are very small and thus the width is reduced down to 39 mm. The efficiency is also very high at lower loads which is the normal operating condition. The mean value is on the whole 93.3% at 230 V ac.

Power boost of 20% enables higher current extraction without voltage drops. This is especially useful during start-ups and to bridge the current peaks in the application. The power reserve can be used continuously up to + 45°C and short periods from +45°C to +60°C.

Short-circuit currents. CP10 can provide short circuit current which is 3 times the nominal current for at least 12 ms, which helps secondary fuses and achieve selectivity. For more information see under Sec. fuses.

Hiccup Plus

With Pulse new short circuit technology ensures optimum protection. The unit leaves a very high short circuit that solves secondary fuses and provide sufficient starting current for example dc motors. If the output voltage drops below 6.5 V dc, a continuous current of 25 A is given for 2 seconds, then turn the assembly of the end to make a new restart attempt after about 18 seconds. This is done until the error has been corrected. This feature ensures a high short-circuit / overload current while avoiding a constant high current that can lead to thermal problems with cables and component damage.

More technical advantages. CP10 has active power factor correction (PFC) and actively protect inrush that effectively reduces start currents which are ideal if several units are connected in the same phase or if the supply is current limited through example. AC UPS. The protection is always active, regardless of the temperature. DC-OK output, wide temperature range, a large number of approvals and transient filter which ensures operation in an interference rich electrical environment makes the unit suitable for virtually all installations. CP10.121 also has an input where the signal turns off the unit.

 

 

Wiring

A: Primary side/control voltage

 

B: Secondary. Output voltage

 

C: potentiometer adjustable output voltage 12-15 V dc

 

D: DC OK LED. Lights when the voltage is 90% of the set value

 

E: DC-OK relay output. Closes when the output voltage is OK

 

F: Inputs for remote shutdown of the unit

Sec. fuses

Breakers is the most common type of fuse for ac voltage but is also used for dc voltages. Power supply always has a current limitation compared with an electricity network which hampers tripping of a circuit breaker of the magnetic field, especially if the voltage is as low as 12 V dc. Greater consideration must be given to the cable diameter and cable lengths. This even if the power supply is able to deliver high short circuit currents. For long cables and/or thin cable area so the solution is electronic fuses.

 

Puls CP10.121 have high short-circuit currents which enables tripping within 10 ms of length and cable section is as below specification.

 

 

Safe tripping of circuit breakers with different cable lengths/diameter

Short-circuit currents. Figure 3-2

 

0.75 mm2

1.0 mm2

1.5 mm2

2.5 mm2

Short circuit currents

C-2A

11 m

15 m

22 m

35 m

C-3A

9 m

13 m

18 m

23 m

C-4A

5 m

8 m

12 m

17 m

C-6A

-

1 m

2 m

3 m

B-6A

6 m

11 m

15 m

23 m

B-10A

2 m

3 m

3 m

4 m

B-13A

1 m

2 m

3 m

4 m

 

Hiccup function Fig 3-3

Hiccup function

Description of Hiccup plus function

Thanks to the unique Pul Hiccupplus ensures a high short circuit current while avoiding the risk of overheated cables and damage to the connected loads. When a short circuit occurs following.

  1. High peak power that enables tripping in 12 ms Figure 3-2.
  2. The unit leaves 25 A for 2 s.
  3. After 2 seconds the unit shuts off, then try to restart every 18 seconds. If the fault is removed, the unit starts automatically, otherwise it will lose further 18 s. The operation does not burden the cabling and does not cause damage to the electronics.  

 

Read more
  • Output current of 16 A
  • Up to 94% efficiency
  • Only 39 mm wide
  • Active current inrush protection

Selected variant

Selected variant

Technical data

Input data

Input voltage ac 100-240 V
Input voltage ac min 85 V AC
Input voltage ac max 264 V AC
Input voltage dc 110-150 V
Input voltage dc min 88 V DC
Input voltage dc max 180 V DC
Inrush current at 120 V ac typical 4 A
Inrush current at 230 V ac typical 4 A
Input voltage range Wide-range
Power factor at 120 V ac, full load. Typical 0,98
Power factor at 230 V ac, full load. Typical 0,91
Number of phases 1

Output data

Output voltage 12 V DC
Output voltage min 12 V DC
Output voltage max 15 V DC
Output current 10 A
Power 120 W

Efficiency / Lifetime / MTBF

Efficiency at 120 V ac, full load, typical 93,2 %
Efficiency at 230 V ac, typical 92,3 %
Efficiency at 230 V ac, full load, typical 94 %
Lifetime at 120 V ac, full load and +40 ° C 94000 h
Lifetime at 230 V ac, full load and +40 ° C 110000 h

Dimensions

Width 32 mm
Height 124 mm
Depth 102 mm
Weight 0,44 kg

Other

Approvals ATEX, CE, cULus, IECEx, IEC 62368-1:2018
Hold time at 120 V ac, typical full load 35 ms
Hold time at 230 V ac, typical full load 35 ms
IP class IP20
Clamp type Screw
Material protection Aluminium
Supply frequency 50-60 ±6 %
Ripple max 50 mV pp
Series Dimension C
Power consumption 120 V ac 1,09 A
Power consumption 230 V ac 0,6 A
Power drop from +60 °C to + 70 °C 3 W/°C
Temperature min without derating -25 °C
Temperature max without derating 60 °C
Type Power Supply AC-DC
DC relay output Yes
Active Transient Yes

Product description

Puls Dimension C-series stands for cost optimization without compromising quality, reliability or performance.

CP10 is the second generation C-series 1-phase that sets new records by using the latest technology and sophisticated thermal design. With an efficiency of 94.3%, the power losses are very small and thus the width is reduced down to 39 mm. The efficiency is also very high at lower loads which is the normal operating condition. The mean value is on the whole 93.3% at 230 V ac.

Power boost of 20% enables higher current extraction without voltage drops. This is especially useful during start-ups and to bridge the current peaks in the application. The power reserve can be used continuously up to + 45°C and short periods from +45°C to +60°C.

Short-circuit currents. CP10 can provide short circuit current which is 3 times the nominal current for at least 12 ms, which helps secondary fuses and achieve selectivity. For more information see under Sec. fuses.

Hiccup Plus

With Pulse new short circuit technology ensures optimum protection. The unit leaves a very high short circuit that solves secondary fuses and provide sufficient starting current for example dc motors. If the output voltage drops below 6.5 V dc, a continuous current of 25 A is given for 2 seconds, then turn the assembly of the end to make a new restart attempt after about 18 seconds. This is done until the error has been corrected. This feature ensures a high short-circuit / overload current while avoiding a constant high current that can lead to thermal problems with cables and component damage.

More technical advantages. CP10 has active power factor correction (PFC) and actively protect inrush that effectively reduces start currents which are ideal if several units are connected in the same phase or if the supply is current limited through example. AC UPS. The protection is always active, regardless of the temperature. DC-OK output, wide temperature range, a large number of approvals and transient filter which ensures operation in an interference rich electrical environment makes the unit suitable for virtually all installations. CP10.121 also has an input where the signal turns off the unit.

 

 

Wiring

A: Primary side/control voltage

 

B: Secondary. Output voltage

 

C: potentiometer adjustable output voltage 12-15 V dc

 

D: DC OK LED. Lights when the voltage is 90% of the set value

 

E: DC-OK relay output. Closes when the output voltage is OK

 

F: Inputs for remote shutdown of the unit

Sec. fuses

Breakers is the most common type of fuse for ac voltage but is also used for dc voltages. Power supply always has a current limitation compared with an electricity network which hampers tripping of a circuit breaker of the magnetic field, especially if the voltage is as low as 12 V dc. Greater consideration must be given to the cable diameter and cable lengths. This even if the power supply is able to deliver high short circuit currents. For long cables and/or thin cable area so the solution is electronic fuses.

 

Puls CP10.121 have high short-circuit currents which enables tripping within 10 ms of length and cable section is as below specification.

 

 

Safe tripping of circuit breakers with different cable lengths/diameter

Short-circuit currents. Figure 3-2

 

0.75 mm2

1.0 mm2

1.5 mm2

2.5 mm2

Short circuit currents

C-2A

11 m

15 m

22 m

35 m

C-3A

9 m

13 m

18 m

23 m

C-4A

5 m

8 m

12 m

17 m

C-6A

-

1 m

2 m

3 m

B-6A

6 m

11 m

15 m

23 m

B-10A

2 m

3 m

3 m

4 m

B-13A

1 m

2 m

3 m

4 m

 

Hiccup function Fig 3-3

Hiccup function

Description of Hiccup plus function

Thanks to the unique Pul Hiccupplus ensures a high short circuit current while avoiding the risk of overheated cables and damage to the connected loads. When a short circuit occurs following.

  1. High peak power that enables tripping in 12 ms Figure 3-2.
  2. The unit leaves 25 A for 2 s.
  3. After 2 seconds the unit shuts off, then try to restart every 18 seconds. If the fault is removed, the unit starts automatically, otherwise it will lose further 18 s. The operation does not burden the cabling and does not cause damage to the electronics.  

 

Accessories

Related products

Related

DC circuit protection PISA M and circuit breakers
Knowledge

Safeguard systems with DC circuit protection

This blog talks all things DC circuit protection including the key components: electronic circuit breakers, fuses and current monitoring devices. As well as how to choose the right protection.

IATECH, the industrial automation technology exhibition OEM automatic
Company news

Recap of IATECH

Did you get a chance to visit IATECH at The Leicester Marriott Hotel? We had over 33 exhibitors and 8 fantastic Tech Talks throughout the day, Read all about the day, here.

zoller and frohlich cable preparation machines
Product news Blog

Book your Cable Preparation Machinery Demo at OEM

To help experience the capabilities of Z+F machines first-hand, we provide an in-depth demonstration and workshop. These sessions will show the machines in action and allow you to understand their features and gain valuable insight into their operation and benefits.

IATECH industrial automation components exhibition in at leicester marriott hotel by OEM Automatic
Company news

OEM introduces IATECH - The Industrial Automation Technology Expo

We are thrilled to announce the launch of IATECH, THe Industrial Automation Technology expo at Leicester Marriott Hotel on 23rd October. The ultimate platform for showcasing our extensive product range and broad business areas, featuring over 50 leading suppliers under one roof!

automation components for specialist vehicles
Blog

Automation Components for Specialist Vehicles

The specialist vehicle industry can include automotive and EV, heavy vehicles such as agriculture and rail, and marine.  This email takes you through some of the various products we offer for specialist vehicle applications.

Wohner power distribution
Product news Blog

Modern Power Distribution

This blog post delves into the key components, current trends, and best practices in power distribution, illustrating the significant impact these systems have on our daily operations and long-term energy strategies.

Parts Input voltage ac min Input voltage dc Input voltage dc max Inrush current at 120 V ac typical Inrush current at 230 V ac typical Power factor at 120 V ac, full load. Typical Power factor at 230 V ac, full load. Typical Output current Power Efficiency at 120 V ac, full load, typical Efficiency at 230 V ac, typical Efficiency at 230 V ac, full load, typical Lifetime at 120 V ac, full load and +40 ° C Lifetime at 230 V ac, full load and +40 ° C MTBF (IEC 61709) 230 V ac, max load, 40 ° C Width Depth Weight Approvals Hold time at 120 V ac, typical full load Hold time at 230 V ac, typical full load Power consumption 120 V ac Power consumption 230 V ac Power drop from +60 °C to + 70 °C Price
85 V AC
110-150 V
180 V DC
4 A
4 A
0,98
0,91
10 A
120 W
93,2 %
92,3 %
94 %
94000 h
110000 h
32 mm
102 mm
0,44 kg
ATEX, CE, cULus, IECEx, IEC 62368-1:2018
35 ms
35 ms
1,09 A
0,6 A
3 W/°C
90 V AC
110-150 V
180 V DC
6 A
9 A
0,99
0,96
16 A
192 W
92,8 %
93,3 %
94,3 %
75000 h
97000 h
690000 h
39 mm
117 mm
0,6 kg
ABS, CB, CE, CSA, EX, GL, IECEx, UL
50 ms
50 ms
1,74 A
0,92 A
4,8 W/°C
90 V AC
110-300 V
360 V DC
6 A
9 A
0,99
0,96
16 A
192 W
92,8 %
93,3 %
94,3 %
75000 h
97000 h
690000 h
39 mm
117 mm
0,6 kg
CE, cULus
50 ms
50 ms
1,74 A
0,92 A
4,8 W/°C

Selected variant

Select a variant in the list

Contact us
If you need any help, you can contact us in one of the following ways:
0116 284 9900
Send e-mail
Use live chat
Do you need help?
Logo

Cookie settings for OEM.CO.UK

Cookies help us improve your experience with us, so in order to be able to handle login information, offer you personalised content and for basic functionality of this website, we use some cookies.

We will never sell on any information about you. 

You can accept all cookies or personalise your cookies preferences, you can also change your cookie preferences at any time by visiting our contact page.

Necessary Cookies

These cookies are necessary for the website to work and can not be turned off in our systems. They are usually used only in response to actions you have taken in connection with a service request, for example when setting personal preferences, logging in or filling out a form.

Analysis and measurement cookies

These cookies allow us to count the number of visits and traffic sources so that we can measure and improve our website performance. They help us know which pages are more or less popular and how visitors navigate around the site. The information that these cookies collect is aggregated and therefore completely anonymous. If you do not allow these cookies, we do not know when you have visited our website.

Marketing cookies

These cookies can be added by our partners. They can use them to create a profile of you, based on your interests, to show you more relevant information. They do not store any personal information - only information about your browser and device. If you do not accept these cookies, you will have a more general and less customized user experience.