Important notice - Our website is under going construction, therefore you may notice some issues. Please bare with us and contact or customer support team if you need any product information - 0116 284 9900
Important notice - Our website is under going construction, therefore you may notice some issues. Please bare with us and contact or customer support team if you need any product information - 0116 284 9900
PULS
Puls Dimension Q is a new generation of power supply unit with very small construction dimensions and many technical benefits. The unit has low inrush current (even with warm starts), active PFC, which provides a power factor close to one, expanded temperature range and active protection against line transients. Furthermore, there is a relay output (DC OK) that is deactivated when the output voltage deviates more than 10% from the set value. The bonus power provides an extra 50% boost with retained 24 V, which is an advantage when connected loads have high starting currents. The unit also has a high short-circuit current that simplifies tripping of secondary fuses. Both the bonus power and short-circuit current are time-limited to 4 seconds to avoid constant overloading of the unit and wiring. High efficiency provides long lifetime and low temperatures. The power supply unit can be connected for 2-phase operation with Inom up to 40°C. For higher temperatures, the load current must be reduced.
We recommend free space of 60 mm above/under the unit and 15 mm at the sides.
Bonus power
The power supply unit has bonus power that enables high power extraction with retained 24 V dc for 4 seconds, which is a major advantage when connected loads have high starting currents, such as the case with motors. How often bonus power can be utilised depends on the application. With the following diagram and formula, the repeat time can be calculated for each application. The bonus power is available as soon as the power supply unit is started and directly after a short circuit.
Bonus power | Operating characteristics |
|
|
|
|
Po | Nominal load current |
Ppeak | Peak current |
To | Time between bonus power |
Tpeak | Peak current I time |
Operating cycle | Tpeak / (Tpeak + To) |
To | Tpeak - (operating cycle * Tpeak) / operating cycle |
Example: Nominal load current (Po) is 15 A. Peak current (Ppeak) is 24 A = 120%. The peak time is 3 seconds. 15 A = 75% of Inom. According to the diagram, the operating cycle is 50%. To = 3 - (0.5 * 3) / 0.5 = 3 Maximum repeat time of bonus power is 3 seconds. | |
Input data |
|
|---|---|
| Input voltage range | Wide-range |
| Input voltage ac | 380-480 V |
| Input voltage ac min | 323 V AC |
| Input voltage ac max | 552 V AC |
| Inrush current at 400 V ac typical | 3 A |
| Number of phases | 3 |
| Power factor at 400 V ac, full load. Typical | 0,94 |
Output data |
|
| Output voltage min | 24 V DC |
| Output voltage | 24 V DC |
| Output voltage max | 28 V DC |
| Power | 480 W |
| Output current | 20 A |
Efficiency / Lifetime / MTBF |
|
| MTBF (IEC 61709) 400 V ac, max loan, +40 °C | 690000 h |
| Lifetime at 400 V ac, full load and +40 ° C | 105000 h |
| Efficiency at 400 V ac, full load, typical | 95 % |
| Efficiency at 400 V ac, typical | 94,2 % |
Dimensions |
|
| Weight | 0,87 kg |
| Depth | 127 mm |
*Invisible Heading* |
|
|---|---|
| Width | 65 mm |
| Height | 124 mm |
Other |
|
| IP class | IP20 |
| Ripple max | 100 mV pp |
| Hold time at 400 V ac, typical full load | 22 ms |
| Power consumption at 400 V ac | 0,79 A |
| Power drop from +60 °C to + 70 °C | 12 W/°C |
| Clamp type | Spring-clamp |
| Temperature min without derating | -25 °C |
| Series | Dimension Q |
| Supply frequency | 50-60 ±6 % |
| Approvals | CB, CE, CSA, CSA US, cRUus, cULus, GL |
| Temperature max without derating | 60 °C |
| Material protection | Aluminium |
| Type Power Supply | AC-DC |
| Active Transient | Yes |
| DC relay output | Yes |
Puls Dimension Q is a new generation of power supply unit with very small construction dimensions and many technical benefits. The unit has low inrush current (even with warm starts), active PFC, which provides a power factor close to one, expanded temperature range and active protection against line transients. Furthermore, there is a relay output (DC OK) that is deactivated when the output voltage deviates more than 10% from the set value. The bonus power provides an extra 50% boost with retained 24 V, which is an advantage when connected loads have high starting currents. The unit also has a high short-circuit current that simplifies tripping of secondary fuses. Both the bonus power and short-circuit current are time-limited to 4 seconds to avoid constant overloading of the unit and wiring. High efficiency provides long lifetime and low temperatures. The power supply unit can be connected for 2-phase operation with Inom up to 40°C. For higher temperatures, the load current must be reduced.
We recommend free space of 60 mm above/under the unit and 15 mm at the sides.
Bonus power
The power supply unit has bonus power that enables high power extraction with retained 24 V dc for 4 seconds, which is a major advantage when connected loads have high starting currents, such as the case with motors. How often bonus power can be utilised depends on the application. With the following diagram and formula, the repeat time can be calculated for each application. The bonus power is available as soon as the power supply unit is started and directly after a short circuit.
Bonus power | Operating characteristics |
|
|
|
|
Po | Nominal load current |
Ppeak | Peak current |
To | Time between bonus power |
Tpeak | Peak current I time |
Operating cycle | Tpeak / (Tpeak + To) |
To | Tpeak - (operating cycle * Tpeak) / operating cycle |
Example: Nominal load current (Po) is 15 A. Peak current (Ppeak) is 24 A = 120%. The peak time is 3 seconds. 15 A = 75% of Inom. According to the diagram, the operating cycle is 50%. To = 3 - (0.5 * 3) / 0.5 = 3 Maximum repeat time of bonus power is 3 seconds. | |
Engineers and technicians are seeking solutions that streamline assembly whilst maintaining high levels of protection and flexibility. KDS-SR90 angled screw frames and inlays bring a new level of efficiency to cable routing with a unique 90° entry design.
The smallest logic controller by Crouzet is now 20% off for a limited time only! A powerhouse packed into just 17.5mm! Efficiency, adaptability, and seamless integration with free software.
Do you require signalling devices and beacons in your production process? Download our latest whitepaper!
Here, our customer requires control boxes for electricity metering systems. We leveraged our expertise to deliver easy-to-install, ready-to-use assemblies. We look forward to creating more of these bespoke control boxes for our customer.
This blog talks all things DC circuit protection including the key components: electronic circuit breakers, fuses and current monitoring devices. As well as how to choose the right protection.
Did you get a chance to visit IATECH at The Leicester Marriott Hotel? We had over 33 exhibitors and 8 fantastic Tech Talks throughout the day, Read all about the day, here.
|
|
|
|
|
|
||
|---|---|---|---|---|---|---|
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
| Parts | Approvals | Conformal coated | Price | ||
|---|---|---|---|---|---|
POWER SUPPLY 24VDC 480W 20A
Art:
QT20.241
Copied
|
CB, CE, CSA, CSA US, cRUus, cULus, GL
|
|
| ||
|
POWER SUPPLY 24VDC 480W 20A COATED
Art:
QT20.241-C1
Copied
|
CB, CE, CSA US, cRUus, cULus, EN 50155, GL
|
Yes
|
|
Select a variant in the list
