Important notice - Our website is under going construction, therefore you may notice some issues. Please bare with us and contact or customer support team if you need any product information - 0116 284 9900
Important notice - Our website is under going construction, therefore you may notice some issues. Please bare with us and contact or customer support team if you need any product information - 0116 284 9900
PULS
Pulse Dimension Q is a series power supply with very high performance and reliability.
QT40.241 have built primary fuses that make it possible to connect the unit without the need for intermediate fuses up to 32 A (UL) which saves space and money. The efficiency is high over a wide load range, which results in reduced power consumption and longer life regardless of load current. An average efficiency is 94.7% with a peak value of 95.3%. The power loss at idle is very low, 9.5 W.
The bonus power provides 50% extra reserve with retained 24 V dc (60 A) which is an advantage when connected loads have high starting currents and to bridge temporary current peaks. The bonus power is limited to 4 seconds to avoid constant overloading of the power supply and wiring. In addition to the bonus effect leave the unit a very high short-circuit current (ms) that helps to secondary fuses. See technical data for example.
Active transient ensure operation also in very störrik electrical environment and also has QT40.241 active inrush current protection, which means a very low starting current, even if the unit has been in operation for a longer time. Especially useful for redundant / parallel-connected systems.
Simple diagnostics via DC-OK relay that falls on the output voltage deviates more than 10% from the set value, a green LED indicates DC-OK, Red LED indicates overload.
The unit can also be remote controlled for on / off function, three different connection options available. See the "Technical data". Can be used instead of expensive DC contactors when you need to break up the 24 V side (NB. The remote control function has no safety circuit and therefore should not be used in the security context).
Active PFC reduces power consumption, harmonics close to zero, in addition, the power distribution in phases much smoother at power asymmetry.
Bonus power
The power supply has bonus power that enables high power extraction with retained 24 V DC for 4 seconds, which is a major advantage when connected loads have high starting currents, such as the case with motors. How often bonus power can be utilised depends on the application. With the following diagram and formula, the repeat time can be calculated for each application. The bonus power is available as soon as the power supply is started and directly after a short circuit.
We recommend free space of 40 mm above and 20 mm under the power supply, and 5 mm at the sides.
Bonus power | Operating cycle |
|
|
Po | Nominal load current |
Ppeak | Peak current |
To | Time between bonus power |
Tpeak | Peak current I time |
Operating cycle | Tpeak / (Tpeak + To) |
To= | Tpeak - (operating cycle * Tpeak) / operating cycle |
Example: Peak current (Ppeak) is 50 A =125%. The peak time is 3 seconds. Nominal load current (Po) is 30 A. 30 A =75% of Inom. According to the diagram, the operating cycle is about 0.45. To = 3 - (0.45 * 3) / 0.45 = 3.6. Maximum repeat time of bonus power is 3.6 seconds. | |
Output characteristic |
|
Remote control function |
|
Input data |
|
|---|---|
| Input voltage range | Wide-range |
| Input voltage ac | 380-480 V |
| Input voltage ac min | 323 V AC |
| Input voltage ac max | 576 V AC |
| Inrush current at 400 V ac typical | 5 A |
| Number of phases | 3 |
| Power factor at 400 V ac, full load. Typical | 0,88 |
Output data |
|
| Output voltage min | 24 V DC |
| Output voltage | 24 V DC |
| Output voltage max | 28 V DC |
| Power | 960 W |
| Output current | 40 A |
Efficiency / Lifetime / MTBF |
|
| MTBF (IEC 61709) 400 V ac, max loan, +40 °C | 375000 h |
| Lifetime at 400 V ac, full load and +40 ° C | 69000 h |
| Efficiency at 400 V ac, full load, typical | 95,3 % |
| Efficiency at 400 V ac, typical | 94,7 % |
Dimensions |
|
| Weight | 1,5 kg |
| Depth | 127 mm |
*Invisible Heading* |
|
|---|---|
| Width | 110 mm |
| Height | 124 mm |
Other |
|
| IP class | IP20 |
| Ripple max | 100 mV pp |
| Hold time at 400 V ac, typical full load | 25 ms |
| Power consumption at 400 V ac | 1,65 A |
| Power drop from +60 °C to + 70 °C | 24 W/°C |
| Clamp type | Screw on |
| Temperature min without derating | -25 °C |
| Series | Dimension Q |
| Supply frequency | 50-60 ±6 % |
| Approvals | CB, CE, CSA, GL, UL |
| Temperature max without derating | 60 °C |
| Material protection | Aluminium |
| Type Power Supply | AC-DC |
| Active Transient | Yes |
| DC relay output | Yes |
Pulse Dimension Q is a series power supply with very high performance and reliability.
QT40.241 have built primary fuses that make it possible to connect the unit without the need for intermediate fuses up to 32 A (UL) which saves space and money. The efficiency is high over a wide load range, which results in reduced power consumption and longer life regardless of load current. An average efficiency is 94.7% with a peak value of 95.3%. The power loss at idle is very low, 9.5 W.
The bonus power provides 50% extra reserve with retained 24 V dc (60 A) which is an advantage when connected loads have high starting currents and to bridge temporary current peaks. The bonus power is limited to 4 seconds to avoid constant overloading of the power supply and wiring. In addition to the bonus effect leave the unit a very high short-circuit current (ms) that helps to secondary fuses. See technical data for example.
Active transient ensure operation also in very störrik electrical environment and also has QT40.241 active inrush current protection, which means a very low starting current, even if the unit has been in operation for a longer time. Especially useful for redundant / parallel-connected systems.
Simple diagnostics via DC-OK relay that falls on the output voltage deviates more than 10% from the set value, a green LED indicates DC-OK, Red LED indicates overload.
The unit can also be remote controlled for on / off function, three different connection options available. See the "Technical data". Can be used instead of expensive DC contactors when you need to break up the 24 V side (NB. The remote control function has no safety circuit and therefore should not be used in the security context).
Active PFC reduces power consumption, harmonics close to zero, in addition, the power distribution in phases much smoother at power asymmetry.
Bonus power
The power supply has bonus power that enables high power extraction with retained 24 V DC for 4 seconds, which is a major advantage when connected loads have high starting currents, such as the case with motors. How often bonus power can be utilised depends on the application. With the following diagram and formula, the repeat time can be calculated for each application. The bonus power is available as soon as the power supply is started and directly after a short circuit.
We recommend free space of 40 mm above and 20 mm under the power supply, and 5 mm at the sides.
Bonus power | Operating cycle |
|
|
Po | Nominal load current |
Ppeak | Peak current |
To | Time between bonus power |
Tpeak | Peak current I time |
Operating cycle | Tpeak / (Tpeak + To) |
To= | Tpeak - (operating cycle * Tpeak) / operating cycle |
Example: Peak current (Ppeak) is 50 A =125%. The peak time is 3 seconds. Nominal load current (Po) is 30 A. 30 A =75% of Inom. According to the diagram, the operating cycle is about 0.45. To = 3 - (0.45 * 3) / 0.45 = 3.6. Maximum repeat time of bonus power is 3.6 seconds. | |
Output characteristic |
|
Remote control function |
|
Engineers and technicians are seeking solutions that streamline assembly whilst maintaining high levels of protection and flexibility. KDS-SR90 angled screw frames and inlays bring a new level of efficiency to cable routing with a unique 90° entry design.
The smallest logic controller by Crouzet is now 20% off for a limited time only! A powerhouse packed into just 17.5mm! Efficiency, adaptability, and seamless integration with free software.
Do you require signalling devices and beacons in your production process? Download our latest whitepaper!
Here, our customer requires control boxes for electricity metering systems. We leveraged our expertise to deliver easy-to-install, ready-to-use assemblies. We look forward to creating more of these bespoke control boxes for our customer.
This blog talks all things DC circuit protection including the key components: electronic circuit breakers, fuses and current monitoring devices. As well as how to choose the right protection.
Did you get a chance to visit IATECH at The Leicester Marriott Hotel? We had over 33 exhibitors and 8 fantastic Tech Talks throughout the day, Read all about the day, here.
|
|
|
|
|
|
||
|---|---|---|---|---|---|---|
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
| Parts | Lifetime at 400 V ac, full load and +40 ° C | Clamp type | Approvals | Price | ||
|---|---|---|---|---|---|---|
POWER SUPPLY 24VDC 960W 40A
Art:
QT40.241
Copied
|
69000 h
|
Screw on
|
CB, CE, CSA, GL, UL
|
| ||
|
POWER SUPPLY 24VDC 960W 40A
Art:
QT40.242
Copied
|
93000 h
|
Screw
|
CB, CE, CSA, UL
|
|
Select a variant in the list
