The OEM offices, workshop and warehouse will be closed for the Christmas period. See our full closing times and last order details.
ELECTROMEN
EM-243C is a full bridge DC-motor starter. It is designed to work with DC-motor in applications where some special functions are needed. Starter has adjustable acceleration and deceleration ramps, which make possible the smooth starts and stops. Adjustable current limit protects motor against overcurrent and it can also be used as an end-stop. This device has also two settable speeds, which are usefull in positioning applications. Control inputs FW and BW start the forward and backward run. STOP is for the motor shut-down but there are also available individual limit inputs for FW and BW directions. SPEED-2 input activates preset speed-2, but it can also be used as input for analog speed control signal 0-5V. FAULT terminal has at the same time input and output function, the pin is normally high, but is pulled down in overheat and conditionally also in current trip situation. If FAULT-line is pulled down externally it will cause a stop and prevent the new start. For example, it is possible to link fault pins of several units together and achieve a syncronous stop. There are 2 selectable control modes, contionuous and impulse. In continuous mode the motor runs as long as the control is active.
In impulse mode a short comand starts the motor, and only a new impulse will change the status. The card has selectable input logics.
Inputs are divided in two groups, control and limit -inputs. Groups can be individually set for NPN or PNP logic. The parameters are set with EM-236 interface unit. Operation of the controller and some of its functional values can also be monitored with EM-236 interface unit. In C-version program is possible to select 16kHz pwm frequency ( = silent ) but notice that current output capability is lower with 16kHz.
Â
FEATURES ( notice Prog. and PCB versions )
- small size
- high current output
- current limit
- zero current limit
- speed setting
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- C ver. card compatible with A version card
- C firmware can be loaded A-ver. card
- C ver. new features
+ freewheel options parameter (param 19)
+ 2 or 16kHz pwm freq.select (param. 20)
+ current limit analog input ( param 6&7 )
+ speed+dir operating mode (param. 5)
+ Fan and Brake available in board 243C v.2
+ Extend operating voltage in board 243C v.2
Â
Â
* Motor current max. with 2kHz pwm
100% pwm 50A , 20-99pwm% 35A and peak 100A ( 5s )
Motor current max. with 16kHz pwm
100% pwm 40A , 20-99pwm% 20A and peak 60A ( 5s )
| Analogue input | 0-5V or 0-10V |
|---|---|
| Control type | Speed, Direction, Torque, Soft start / stop |
| Current limit | 1-100 A |
| Current setting range | 1-100 A |
| Dimensions length x width x height | 107x72x40mm mm |
| Logic input high | >4V = ON |
| Logic input low | <1V = OFF |
| Max continuous current | *50 A |
| Mounting | DIN rail |
| Operating temperature | -40°C...+60°C |
|---|---|
| Peak current | (5s) 100 A |
| PWM frequency | 2kHz/16kHz |
| Suitable engine | DC |
| Supplier | Electromen |
| Supply voltage | 12 V DC, 24 V DC, 36 V DC, 48 V DC |
| Weight | 190 g |
EM-243C is a full bridge DC-motor starter. It is designed to work with DC-motor in applications where some special functions are needed. Starter has adjustable acceleration and deceleration ramps, which make possible the smooth starts and stops. Adjustable current limit protects motor against overcurrent and it can also be used as an end-stop. This device has also two settable speeds, which are usefull in positioning applications. Control inputs FW and BW start the forward and backward run. STOP is for the motor shut-down but there are also available individual limit inputs for FW and BW directions. SPEED-2 input activates preset speed-2, but it can also be used as input for analog speed control signal 0-5V. FAULT terminal has at the same time input and output function, the pin is normally high, but is pulled down in overheat and conditionally also in current trip situation. If FAULT-line is pulled down externally it will cause a stop and prevent the new start. For example, it is possible to link fault pins of several units together and achieve a syncronous stop. There are 2 selectable control modes, contionuous and impulse. In continuous mode the motor runs as long as the control is active.
In impulse mode a short comand starts the motor, and only a new impulse will change the status. The card has selectable input logics.
Inputs are divided in two groups, control and limit -inputs. Groups can be individually set for NPN or PNP logic. The parameters are set with EM-236 interface unit. Operation of the controller and some of its functional values can also be monitored with EM-236 interface unit. In C-version program is possible to select 16kHz pwm frequency ( = silent ) but notice that current output capability is lower with 16kHz.
Â
FEATURES ( notice Prog. and PCB versions )
- small size
- high current output
- current limit
- zero current limit
- speed setting
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- C ver. card compatible with A version card
- C firmware can be loaded A-ver. card
- C ver. new features
+ freewheel options parameter (param 19)
+ 2 or 16kHz pwm freq.select (param. 20)
+ current limit analog input ( param 6&7 )
+ speed+dir operating mode (param. 5)
+ Fan and Brake available in board 243C v.2
+ Extend operating voltage in board 243C v.2
Â
Â
* Motor current max. with 2kHz pwm
100% pwm 50A , 20-99pwm% 35A and peak 100A ( 5s )
Motor current max. with 16kHz pwm
100% pwm 40A , 20-99pwm% 20A and peak 60A ( 5s )
Did you get a chance to visit IATECH at The Leicester Marriott Hotel? We had over 33 exhibitors and 8 fantastic Tech Talks throughout the day, Read all about the day, here.
We are thrilled to announce the launch of IATECH, THe Industrial Automation Technology expo at Leicester Marriott Hotel on 23rd October. The ultimate platform for showcasing our extensive product range and broad business areas, featuring over 50 leading suppliers under one roof!
The specialist vehicle industry can include automotive and EV, heavy vehicles such as agriculture and rail, and marine. This email takes you through some of the various products we offer for specialist vehicle applications.
AGV drive wheel motors cover a wide range of options – from a miniature unit on a small 20kg robot, tasked to move on a perfectly level and smooth indoor surface, up to passenger vehicle-sized robots working outside over fields and varying terrain.
At OEM Automatic, we can supply a series of components for your one project. All under one roof. This case study discusses how we supplied several components for our customer's new electro-pneumatic control box.Â
Technosoft specialise in developing intelligent drives and certainly live up to the term 'intelligent’, by combining a powerful motor and motion controller to implement complex movements.
|
|
|
|
|
|
||
|---|---|---|---|---|---|---|
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
| Parts | Analogue input | Brake output | Change direction of rotation (CW/CCW) | Control type | Current limit | Current limit adjustable | Current setting range | Currenttrip autoreveice | Dimensions length x width x height | Forward/Reverse | Functions | Impulse/continuous mode | Joystick analog input | Logic input high | Logic input low | Max continuous current | Parallel driver four motors | Parallel driver two motors | Peak current | Position with potentiometer | Positioning | Potentiometer adjustable speed | PWM frequency | RS232 | RS485/Modbus | Softstart/stop | Speed settings | Speedregulator | Stop at limit position | Suitable engine | Supplier | Supply voltage | Price | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
DC motor 2Q drive 12-42Vdc, 50A
Art:
EM-243C*
Copied
|
0-5V or 0-10V
|
|
|
Speed, Direction, Torque, Soft start / stop
|
1-100 A
|
|
1-100 A
|
|
107x72x40mm mm
|
|
|
|
|
>4V = ON
|
<1V = OFF
|
*50 A
|
|
|
(5s) 100 A
|
|
|
|
2kHz/16kHz
|
|
|
|
|
|
|
DC
|
Electromen
|
12 V DC, 24 V DC, 36 V DC, 48 V DC
|
| ||
DC motor 2Q drive 12-42 V dc, 50 A
Art:
EM-243C
Copied
|
0-5V or 0-10V
|
Yes
|
Yes
|
Speed, Direction, Torque, Soft start / stop
|
1-100 A
|
Yes
|
1-100 A
|
Yes
|
107x72x40mm mm
|
|
Currenttrip autoreversing, Brake output, Speed settings, Impulse/continuous mode, Joystick analog input, Softstart/stop, Potentiometer adjustable speed, RS485/Modbus, Stop at limit position, Speedregulator, Change direction of rotation (CW/CCW)
|
Yes
|
Yes
|
>4V = ON
|
<1V = OFF
|
*50 A
|
No
|
No
|
(5s) *100 A
|
No
|
No
|
Yes
|
2kHz/16kHz
|
No
|
No
|
Yes
|
Yes
|
Yes
|
Yes
|
DC
|
Electromen
|
12-48 V DC
|
| ||
|
DC motor positioning drive 12-24 V dc, 50 A, pulse FB
Art:
EM-243-SPF
Copied
|
|
Yes
|
Yes
|
|
|
|
1-100A
|
|
|
Yes
|
|
|
|
|
|
|
No
|
No
|
(1s) 150 A
|
Yes
|
Yes
|
No
|
|
|
|
Yes
|
Yes
|
Yes
|
Yes
|
|
|
12-48 V DC
|
|
Select a variant in the list
